Mexican Lava Stone Metate
About the piece
Care and Use
How it’s Made
The Metate is a great historical tool to finely grind corn to make tortillas or atole. It can also be used to grind seeds, dry chiles, and spices. The Metate comes with the grinder that measures 8.5in in lenght. The Metate we carry is completely hand carved by our artisans in Mexico from a single block of the best quality basalt volcanic rock through a laborious chipping process. Will last many years with proper use and care. Completely natural and safe, contains no toxins or lead.
|How we measure|
For best result, do not put your Metate in a dishwasher, instead hand wash it under running water, using a mild soap, avoiding strongly scented soaps which can flavor the rock. In fact, some people do not use soap at all to better retain the flavors. Dry thoroughly.
To sanitize a Metate, clean the entire piece well with soap and hot water, then rinse and place it in a 350 degree oven for approximately 15 to 20 minutes.
As with most products which are handmade by artisans around the world, the pieces may have slight imperfections in the form or finish of the materials. Sometimes sizes of same model pieces may also vary slightly, however, these imperfection do not compromise the aesthetics or functionality of the pieces and are considered normal and expected.
Before using the first time, a Metate should be “broken into” to make sure that there are no small grains of rock that can become loose when used for the first time.
You do this by grinding a handful of raw rice several times in the basis of the Metate with the Mano, or grinder using the rice as an abrasive agent to grind the surface of the basis smooth. Keep grinding the rice until it becomes grey from the rock “dust”. Dust of the basin, and keep repeating the process with new rice until the rice no longer turns grey. Some people prefer to do this outside as the grains of rice tend to grains jump out. Although a laborious process, once done, you will never have to do it again. Some rice flour will remain ground into the surface of the rock, but this does not create any problems.
The making of a molcajete is probably one of the arduous tasks in the entire culinary chain world. The process, which has remained unchanged for thousands of years, involves countless hours of an artisan, crouched over a piece of basalt volcanic rock, and slowly chipping away at it with rudimentary tools until the familiar molcajete appears.
The process is more complicated than that and it really begins by making those rudimentary tools made by the artisans themselves. Forged out of iron, the different axes they use are sharpened by fire and the help of hammers and anvil.
To get the raw materials the artisans use to make the molcajetes, they have to travel to the quarries where the proper basalt volcanic rocks are found. Once the stones are selected, they begin by splitting off flat slabs. After repeatedly hitting a rock at the desired width of the slab with a sharp axe, fissures begin to form and with the help of wedge point crowbar and brute force, they break off large flat slabs of the rock.
Once the slabs are on the ground, the artisans then begin to break off smaller sections, more or less the size of what the ultimate molcajete will be.
With the slab now in smaller sections, the artisan then begins to chip away at it to make short cylinders roughly the size of what the ultimate molcajete will be. Usually, this chipping process is done on the ground as they hold the section of rock between their feet. Once he has formed sufficient cylinders, he ties them together in a stack, and with the help of his burro, transports them back to his work place, which is normally no more than a shady spot behind their home, to begin the detail work on the molcajete.
The cylinders are repeatedly trimmed by the artisan’s axes until almost perfect cylinders are formed with a diameter of the ultimate molcajete. The artisans normally start by chipping away at the rock to form the legs as they are the most delicate part, easily broken with the slightest wrong hit of the axe, The process takes a great deal of strength and stamina, yet hitting the rock delicately and with precision. As the process continues, all the while, sitting on the floor and holding the rock between their feet, the legs slowly begin to appear from the dust, which cover everything and turn everything grey. The legs are trimmed using narrower axes until they reach the correct dimensions and are ground smooth by the sharp instrument and delicate, but brute force.
The forming molcajete is then turned over, and the process of digging out the bowl section begins. The artisan carefully begins hitting the center of the mocajete with a blunter axe, which slowly begins to chip away a bowl like cavity in the rock. Eventually smaller, sharper axes are used to finely smooth the bowl.
The entire piece is then given a smoothing with the fine axe, and the final product is ready!